20 Most Recent 2007 MBK XLimit SM - Page 3 Questions & Answers

0helpful
1answer

06 boulevard c50, changed turn signals to led's and now have absolutely nothing. Running lights are on, no turn signal. Fuse is good. I'm seeing two different relays online, is it one or both?

If you have the traditional thermo-mechanical flasher, the LEDs may not pass enough current for the flasher to work correctly. Flashers use a bimetal strip heated by resistance wire wrapped around it. The lamp current heats the strip until it snaps the circuit open, turning the lamps off. When the strip cools, it goes back to the on position and the cycle repeats. If a lamp is burned out, the strip doesn't go as far in the off position, so you see a rapid flash. I suspect the LEDs turn on and stay on when you try the turn signal. Your alternatives are to kluge the circuit with a resistor in parallel with one LED on each side, or to find an electronic flasher
6/7/2024 1:34:56 AM • Motorcycles • Answered on Jun 07, 2024
0helpful
1answer

83 Ford 4.9 runs great for about 10 min then just quits. New carb, filter, lines, pump to a clear line filter that is full with fuel also has new ignition module. At wits end. Please Help!!

It sounds like you've already tackled many of the common issues, so let's focus on a few other possibilities: 1. **Ignition Coil**: When the engine quits, check if you still have spark. A failing ignition coil can work when cold but fail as it heats up. 2. **Fuel Delivery**: Even though you see fuel in the clear line filter, it's worth checking the fuel pressure. The pump might be failing after it runs for a while. 3. **Vapor Lock**: Ensure the fuel lines aren't too close to hot engine parts, which could cause the fuel to vaporize and block the flow. 4. **Electrical Connections**: Check all the wiring and connectors for loose or corroded connections, especially around the ignition system. 5. **Fuel Cap Vent**: Make sure the fuel tank is venting properly. Try running the engine with the gas cap loosened to see if it keeps running longer. By systematically checking these areas, you should be able to pinpoint the issue. Good luck!
6/3/2024 6:03:00 AM • Motorcycles • Answered on Jun 03, 2024
0helpful
1answer

Optisan star 36050 owner manual needed

https://www.apm-telescopes.de/media/manuals/skywatcher/en/12.pdf
6/2/2024 10:23:01 AM • Motorcycles • Answered on Jun 02, 2024
0helpful
1answer

Do u keep the bike straight to check drive shaft fuild

check/fill it while it's in the straight up position, 99.9% of the dealers do the same thing when they these service bikes. Best to you.
5/16/2024 7:45:32 PM • Motorcycles • Answered on May 16, 2024
0helpful
1answer

I have an E-5 error code what does this mean?

You posted to the category 'Motorcycles'? All Questions need full 'make model (what it is)' first 3 words. What is the code E5 on the Mighty Jet? Error Codes: E2: Under Voltage Protection - Input Voltage Under 12V. E3: Over Current Protection - Input Current Over 2.5amp. E4: Dry Run Protection - Pump Out of Water. E5: Impeller Seized - Impeller Not Spinning. Some E5 Jet videos
5/14/2024 1:39:52 PM • Motorcycles • Answered on May 14, 2024
0helpful
1answer

HOW TO REMOVE seat from a skyjet 125 23

a motorcycle, it is. not a car well most cycles made it tilts out even needing key unlock then the seat hinges are unbolted. but not all. do that. the manual covers that buy one/ https://duckduckgo.com/?hps=1&q=skyjet+sj123-23+manual&atb=v403-1&ia=web
5/11/2024 11:32:46 AM • Motorcycles • Answered on May 11, 2024
0helpful
1answer

Goldwing radio lcd display not working

2004 Goldwing radio works no display trip gage no display speedometer doe's not work need help please
5/9/2024 12:31:35 PM • Motorcycles • Answered on May 09, 2024
0helpful
1answer

Where can i buy second hand immobiliser for multistrada 1000ds

  1. Check online platforms such as eBay, Craigslist, or motorcycle forums. These platforms often have listings for used motorcycle parts, including immobilizers. Be sure to search specifically for your bike model to find relevant listings.
  2. Local Motorcycle Shops: Visit local motorcycle shops or repair centers. They might have used parts available for sale or be able to connect you with other riders who are selling immobilizers.
  3. Ducati Enthusiast Groups: Join Ducati enthusiast groups on social media or forums. Fellow Ducati owners may have spare parts they're willing to sell or trade.
  4. Motorcycle Salvage Yards: Contact motorcycle salvage yards or scrapyards. They often have a wide range of used parts from various bike models.
Remember to verify the compatibility of any second-hand immobilizer with your specific Multistrada 1000DS model before making a purchase. FIM Replacement ECU: You can check with FIM (Fuel Injection and Mapping) as they offer a replacement ECU that bypasses the immobilizer. Although it's a bit pricey at USD $725 retail, it provides more adjustability and versatility compared to a Power Commander (PC3). Keep in mind that not many places in the US can map these ECUs.
4/30/2024 10:09:49 AM • Motorcycles • Answered on Apr 30, 2024
0helpful
1answer

What's the tappet clearance of boxer 150cc when using feeler gauge.

Intake 0.05mm, Outlet 0.07mm/0.08mm
4/26/2024 2:16:53 PM • Motorcycles • Answered on Apr 26, 2024
0helpful
1answer

What causes my fat boy to idle just fine but fall on its face back fire and try to shut down while riding

Some common causes and potential solutions: Air/Vacuum Leak: If your Harley develops a vacuum leak in its air intake system, the air-fuel mixture becomes too rich. This can cause frequent stall outs, especially after the bike warms up. Vacuum leaks often occur due to dried-out or cracked air intake boots, faulty gaskets, or worn-out carburetor seals. When air escapes from the intake system, the fuel fills the empty space in the combustion chamber, altering the air/fuel ratio and negatively impacting combustion. Severe vacuum leaks can lead to excess fuel flowing into the exhaust system, causing backfiring and stalling while riding. Clogged Fuel Tank Filter/Fuel Injectors: A blocked fuel tank filter (due to coagulated fuel, moisture, dirt, or corrosion) impairs fuel flow, resulting in a lean air/fuel ratio. On fuel-injected Harleys, clogged fuel injectors produce similar symptoms. Regular maintenance, including cleaning and inspecting fuel filters, helps prevent these issues. Faulty Cam Chain Tensioner: A malfunctioning cam chain tensioner can affect engine timing and cause stalling. Regular checks and replacements are essential to avoid this problem. Faulty Cam Position Sensor: The cam position sensor plays a crucial role in ignition timing. If it malfunctions, it can lead to stalling and backfiring. Clogged Air Cleaner: A dirty air cleaner restricts airflow, affecting combustion efficiency. Regularly clean or replace the air filter to prevent this issue. Ignition System Failure: Faulty ignition components (such as spark plugs, ignition coils, or wires) can cause misfires, backfires, and stalling. Inspect and maintain these parts regularly. Compromised Battery Terminal Connection: Poor battery connections can disrupt electrical flow, affecting the ignition system. Ensure clean and secure battery terminals. Remember that diagnosing and addressing these issues may require professional assistance. Regular maintenance and timely repairs can keep your Fat Boy running smoothly on the road.
4/21/2024 6:14:37 PM • Motorcycles • Answered on Apr 21, 2024
0helpful
1answer

Engine number location on a 2007 c90

Honda C90, or Suzuki C90? all questions need full 'year make model'. Google it plus 'engine number location'. ..
4/21/2024 2:56:52 AM • Motorcycles • Answered on Apr 21, 2024
0helpful
1answer

Need circuit diagram for ARLEC 15e 6-24Volt 15Amp Electronic battery charger OR their later model BC58

I can't find a diagram. The small potentiometer on the control board likely serves as an adjustable component to fine-tune specific parameters. Here are some possibilities: Voltage Regulation: The potentiometer might control the output voltage. By adjusting it, you can set the desired charging voltage for different battery types (e.g., 6V or 12V). Current Limit Adjustment: It could be used to set the maximum charging current. Adjusting the potentiometer allows you to limit the charging current based on the battery's capacity and condition. Sensitivity or Threshold: Some potentiometers act as sensitivity controls. For example, it might adjust the threshold at which the charger switches between charging and maintenance modes. Setting the Potentiometer: Without the specific circuit diagram or detailed information about your charger, I recommend the following general steps: Observe the Potentiometer: Identify the potentiometer on the control board. Note its position and any markings (if present). Consult the User Manual: Check the user manual or operating instructions. It might provide guidance on adjusting the potentiometer. Trial and Error: If no specific instructions are available, start with the potentiometer set to its mid-position. Gradually adjust it while monitoring the charger's behavior (e.g., charging current, voltage). Observe how the charger responds to changes in the potentiometer setting. Fine-tune it based on your specific battery type and desired charging characteristics. Remember that precise adjustments depend on the charger's design and the battery you're charging.
4/20/2024 3:30:25 AM • Motorcycles • Answered on Apr 20, 2024
0helpful
1answer

What is the length of lift cables on a 1993 model 2693 hilo camper and any info on what after market part to use ? thanks

The lift cables on a 1993 model 2693 Hilo camper are 30 feet,2 3/4 inches long and fit the standard height lift of 11 feet 8 inches high to the top of the overhead. The lift uses two cables. According to a Hi- Lo camper travel trailer forum, cable replacement is basically the same on all years and models, with the main difference being the length of the cables from model to model. You can use a cable cut chart to find what cable length you need for your camper, and you'll need to know your year, model name, and box (body) length: Lift cables typically wear out after three to five years, so it's important to replace them as needed and keep them regularly maintained.
4/12/2024 1:26:15 AM • Motorcycles • Answered on Apr 12, 2024
0helpful
1answer

Mine is a 410JS 1000cc Santana, Spanish made. Mechanical fuel pump does bring no fuel to the carb. Want to shift to an electric setup. What is the best pump? Do I need an overflow-line?

The bike doesn't exist as written. https://www.google.com/search?q=410JS+1000cc+santana We are better with 'year make model 1000cc'. Better to not try and do better than the bike engineers. A mechanical pump runs when the engine is turning, an electric pump will run as soon as the key is turned and create pressure all the time. It would have to be an in tank electric pump or it will burn out. Electric pumps are cooled an lubricated by the fuel passing through it. If it is a carbureted engine, you are pressurizing the carb bowl. If injected, it may already have a fuel return. Check the mechanical pump for a torn diaphragm, they are easy to change. ..
3/22/2024 10:35:55 PM • Motorcycles • Answered on Mar 22, 2024
0helpful
1answer

2019 Yamaha YZF R15 V3 with 34,000 km driven. The issue is bike at low rpm bike get off frequently and won't start. Sometimes when I accelerate there is lot in delay in acceleration.

Question edited for clarity and add maker. Try cleaning the Throttle Body. This bike works the same as a car. My first thought was that it has a diaphragm carburetor and the membrane was punctured or split. This bike is not sold in North America https://www.google.com/search?q=yamaha+yzf+r15+v3+clean+throttle+body ..
3/13/2024 10:56:26 PM • Motorcycles • Answered on Mar 13, 2024
0helpful
1answer

Lexmoto Michigan EFI 125 Euro 5. How to remove the battery cover on a Lexmoto Michigan 125 efi please?

Question edited for clarity. Usually, there are two ways, you either remove a side cover and it comes out sideways, or you remove the seat and it lifts out. https://www.google.com/search?q=lexmoto+michigan+125+efi+battery+cover+removal https://www.google.com/search?q=lexmoto+michigan+125+efi+manual ..
3/9/2024 7:37:19 PM • Motorcycles • Answered on Mar 09, 2024
0helpful
1answer

Hero Honda Karizma R valve clearance please?

Question edited for a lot more clarity. Hero Honda Karizma R 0.10 mm on both inlet and exhaust https://www.facebook.com/WonderMechanicAjayKumarSavita/photos/a.1615112108760566/2952364698368627/?type=3 ..
3/9/2024 1:41:57 AM • Motorcycles • Answered on Mar 09, 2024
0helpful
1answer

How to fix a Pit Bike with no spark please? nosprk pitbike

Question translated for clarity and into written English. :>D Test the coil, test the CDI or Contact Breaker Points if it has them. All questions need 'year make model', or at very least 'make and model' please. Help in the link https://www.google.com/search?q=Pit+Bike+with+no+spark ..
3/6/2024 6:42:06 AM • Motorcycles • Answered on Mar 06, 2024
Not finding what you are looking for?
2007 MBK XLimit SM Logo

0 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top MBK Experts

ADMIN Andrew
ADMIN Andrew

Level 3 Expert

73781 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

7373 Answers

ADMIN Eric
ADMIN Eric

Level 3 Expert

42220 Answers

Are you a MBK Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Grizzly 12 MBK

  • Grizzly 12 MBK

Most Popular Question

get replacement speedometer hub sit

  • Motorcycles
Loading...