20 Most Recent
DeVilbiss Finishline Flg-647 Hvlp Spray Paint Gun 2 Tip - Page 9 Questions & Answers
Bostitch SX1838K 18GA Narrow Crown Finish Brad Nailer and Stapler. I bought a lightly used SX1838. Tested it a few months ago. Took me a minute to get it to fire but it seemed to be fine.
If your SX1838 is not firing when you try to use it on your carpet project, there may be a few possible issues that you can try to address. Here are some steps you can take to troubleshoot the problem:
- Check the power source. Make sure that the power cord is securely plugged into the SX1838 and into a working outlet. If the power cord is damaged or not properly connected, the tool may not be receiving enough power to operate.
- Check the switch. The SX1838 has a switch that allows you to select between two modes of operation. Make sure that the switch is set to the correct mode for your project.
- Check the trigger. The SX1838 is triggered by pressing the trigger on the handle. Make sure that the trigger is fully depressed and that it is not obstructed by any debris or other materials.
- Check the nozzle. The SX1838 has a nozzle that sprays the adhesive. Make sure that the nozzle is clear and not clogged with any debris or adhesive.
If you are still unable to get the SX1838 to fire after trying these steps, you may need to contact the manufacturer for additional troubleshooting assistance or to have the tool serviced.
How do I take the pin out of saftey neutral switch 2004 monte carlo ls
To remove the pin from the safety neutral switch on a 2004 Monte Carlo LS, you will need to locate the switch and locate the pin. The safety neutral switch is typically located on or near the transmission, and it may be necessary to consult your vehicle's owner's manual to find its exact location. Once you have located the switch, you should be able to see the pin that holds it in place. To remove the pin, you will need to use a tool such as a small flathead screwdriver or a nail to push it out. Gently push the tool against the pin until it pops out of the switch. Be careful not to damage the switch or any other nearby components while removing the pin.
O-ring size for bostitch sb-1850bn trigger unit
Hi,
if this data is not in any of the documents that came with the nailer kit product, please work with one of Bostitch vendor partners for the product in order to acquire the ring size information. Some of these vendor partners would be Lowe's and Walmart. You can call ahead before attempting to visit each partner.
Thank you.
How to check and maintain oil for CP 0200608 coleman powermate 6 gallon
on the compressor end is a plug that when removed is is oil level dipstick. you will need to ad 30 weigh non detergent oil until level is correct by measuring with dip stick. do not overfill, if you do you will need to empty by tipping compressor of on it side.. where did smoke come from . did it smell like oil burning or electrical.
My titan 400I won't prime what can be wrong with it?
OK, Just solved this problem with my Titan 400 not priming....After searching the internet I got the clue that it was the inlet ball valve being stuck. Most said it was from leaving paint in the system or poor cleaning habits. I thought "Not me, I always do a good job cleaning the sprayer and leaving pump preserver in the system when storing". But I was wrong. After disassembling the inlet valve housing (shown in the manual) I found the valve ball stuck to the seat. After freeing the ball there was tiny bit of paint on the seat but it was enough to prevent it from functioning. Reassembled and it works fine. So maybe just luck of the draw. I don't use the system too often and it had been 6 months since the last use...still I stored it with line full of pump preservative. Symptoms were that when in prime it would not **** from the siphon tube (supply) but motor ran fine. A bit painful fix but not terrible, exercise cost me an hour, but next time would take maybe 15 minutes to correct. Hope this helps.
Not getting any air pressure
Larry when you turn your compressor on do you any sounds? I need a little more info I want to help I just need the information Good Luck Mike L
My sullair 185 will not idle down
Hi,
Please attempt to disengage the clutch of the compressor while simultaneously lowering the engine speed.
If this doesn't work, please call Suilar at 1-219-879-5451.
Thank you.
Not finding what you are looking for?
