1
Steve Bowen posted an answer for this Radio Communications:
"flashing display means that the pll is out of lock, the radio needs to be serviced"
Steve Bowen
Steve Bowen posted an answer for this Uniden Bearcat Pro PC68XL 40-Channels Base CB Radio:
"it's not possible to wire 4 wire mics to the uniden 5 wire radios without modifying the..."
Steve BowenSteve Bowen posted an answer for this Magnum 257 CB Radio:
"sounds like the PA has failed, I would have the radio shop serviced"
Steve BowenSteve Bowen posted an answer for this Radio Communications:
"radio is out of alignment. Have the radio shop aligned and all will be well"
Steve BowenSteve Bowen posted an answer for this Radio Communications:
"4 wire mics can't be wired to 5 pin unidens without extremely modifying the mic and..."
Steve BowenSteve Bowen posted an answer for this Radio Communications:
"The ic-735 has to have the keyer option to use with a paddle, if it doesn't you will have..."
Steve BowenSteve Bowen posted an answer for this Radio Communications:
"if the green rx light is off, it's more than likely a failed mic, if it's on and not..."
Steve Bowen
Steve Bowen posted an answer for this Uniden Pro 520 XL:
"generally, a standard AM only CB will use a 3amp fuse."
Steve BowenSteve Bowen posted an answer for this Radio Communications:
"sounds like the mic is miswired or failed"
Steve Bowen
Steve Bowen posted an answer for this Magnum S380 Amateur 10 Meter Radio, AM/FM Radio, 80 watts, Front Panel 4-Pin Microphone Jack, Variable Power Output Control, TURBO Digital Echo with Dual Controls, AMT All Mode Talkback with Volume Control on Front Panel, Front Panel Band Switch, High SWR W:
"check the fuse and power to the radio, if they are good, have the radio serviced"
Steve BowenSteve Bowen posted an answer for this Radio Communications:
"the PA has been damaged, radio needs shop servicing"
Steve BowenSteve Bowen posted an answer for this Superstar SS-121 120-Channels Base CB Radio:
"sounds like the PA has failed. Have a shop check it for ya, they usually will test for..."
Steve BowenSteve Bowen posted an answer for this Magnum 257 CB Radio:
"I wouldn't do this...makes them splatter and sound like hell"
Steve BowenSteve Bowen posted an answer for this Radio Communications:
"sounds like the mic or it's cord has failed, try replacing the mic and it will prbably be..."
Steve Bowen
Steve Bowen posted an answer for this Cobra 29 WX NW ST 40-Channels Base CB Radio:
"sounds like the radio is out of alignment or the pll has failed. have the radio serviced"
Steve Bowen
Steve Bowen posted an answer for this Connex 3300 240-Channels Base CB Radio:
"actually, non of them are, that radio is actually not legal on the CB service in the US"
Steve BowenSteve Bowen posted an answer for this Connex Radio Communications:
"this usually just blows the fuse, check/replace and try again, if it pops the fuse, the..."
Steve BowenSteve Bowen posted an answer for this Radio Communications:
"I assuming you mean stored in the trunk and not operating, if so, no it wont damage it"
Steve BowenSteve Bowen posted an answer for this Radio Communications:
"yes, very quickly"
Steve Bowen
Steve Bowen posted an answer for this Yaesu FT-2900R 75 Watt 2 Meter VHF Mobile Transceiver Amateur Ham Radi:
"if a reset has failed, these means either the eprom or the cpu is damaged."
Steve BowenSteve Bowen posted an answer for this Connex Radio Communications:
"I'm assuming you mean just the knob, and not the shaft behind it, if it's a D shaped..."
Steve BowenSteve Bowen posted an answer for this Radio Communications:
"it's not possible without modifying the mic and changing the mic cord"
Steve BowenSteve Bowen posted an answer for this Radio Communications:
"sizing a power supply is simple.....look at the fuse in the radio, and add about 40-50% to..."
Steve BowenSteve Bowen posted an answer for this Radio Communications:
"take it to a shop that does it for a living, they have the test equipment needed to p-n-t..."
Steve Bowen
Steve Bowen posted an answer for this Connex Cx-3600Hp 3600Hp 10 Meter 100 Watt Cb Radio:
"This means that your swr is high. you can damage the radio using it in this condition, ..."
Steve BowenSteve Bowen posted an answer for this Radio Communications:
"sounds like a personal problem"
Steve Bowen
Steve Bowen posted an answer for this Uniden GRANTLT 40-Channels Base CB Radio:
"Take this to a shop that does it for a living, they have the correct equipment needed to..."
Steve Bowen
Steve Bowen posted an answer for this Uniden CB Radio with SSB Bearcat 980 SSB:
"check that the rf gain is set at maximum, also, I would check antenna and coax for..."
Steve Bowen
Steve Bowen posted an answer for this Midland 1001Z 40-Channels Base CB Radio:
"bolted to a heatsink at the rear of the radio"
Steve Bowen
Steve Bowen posted an answer for this Galaxy Radios DX-2547 40-Channels Base CB Radio:
"Take it to a shop that does it for a living. They have the test equipment needed to do a..."
Steve BowenSteve Bowen posted an answer for this Ranger RCI-6900F-150 CB Radio:
"try turning the mic gain down for a start, if that doesn't correct it, sounds like the..."
Steve Bowen
Radio Communications 83 answers
