3Retired, but not dead yet.
Anonymous posted an answer for this Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum:
"Check the brush end bearings for debris build-up and sticking bearings--remove the brush..."
AnonymousAnonymous posted an answer for this Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum:
"The brush on the our progressive conister stops and starts. We have replaced the belt..."
Anonymous
Anonymous posted an answer for this Garden:
"cutting 5" log with resaw blade. blade heads to the left within 4" of the cut..."
AnonymousAnonymous posted an answer for this Garden:
"Check the teeth tips on the right side of the blade--they may have been dulled by running..."
Anonymous
Anonymous posted an answer for this Whirlpool Washing Machines:
"I have an older Whirpool called Ultimate Care II. Why dosen't this washer come with some..."
AnonymousAnonymous posted an answer for this Whirlpool Washing Machines:
"There is a water level switch that operates with rising air pressure (and rising water..."
Anonymous
Anonymous posted an answer for this 2002 Toyota RAV4:
"how do you get the postive battery cable off to put new one on"
AnonymousAnonymous posted an answer for this Garden:
"I'm not familiar with this particular machine, but in general, I can possibly help. If..."
AnonymousAnonymous posted an answer for this Garden:
"i have a hobart 4030D this machine dont have output of voltage in the terminals and output..."
AnonymousAnonymous posted an answer for this Garden:
"If you don't have the original belt that is intact, then you will have to do some..."
AnonymousAnonymous posted an answer for this Garden:
"I need a belt for my Chicago Forge bandsaw. Where can I get one? I know it is old because..."
AnonymousAnonymous posted an answer for this Garden:
"How do i get the pulley off the shaft of the belt drive on a1313314 delta motor for a..."
AnonymousAnonymous posted an answer for this Garden:
"There should be one or two set screws on the pulley hub that should be backed out several..."
AnonymousAnonymous posted an answer for this Garden:
"Check for a weak/collapsed spring on the sparking brush. Also check the brush holder for..."
AnonymousAnonymous posted an answer for this Garden:
"flashing on carbon brush, even after replasing field coil, armature and carbon brush."
Anonymous
Anonymous posted an answer for this 2005 Dodge Ram 1500:
"Sounds like the engine is running in 'limp in' mode, which should have turned on the check..."
AnonymousAnonymous posted an answer for this 2005 Dodge Ram 1500:
"i recently replaced my egr valve as well as one of my oxy sonsors, was getting 20-22 mpg..."
Anonymous
Anonymous posted an answer for this Homelite Gas, 20 In. Bar, 46 CC, Chain Saw, UT10520:
"50:1 is the fuel to oil ratio using a modern synthetic saw oil available at home centers,..."
AnonymousAnonymous posted an answer for this Homelite Gas, 20 In. Bar, 46 CC, Chain Saw, UT10520:
"need fuel mixture specs"
AnonymousAnonymous posted an answer for this Garden:
"i have a 5 hp tecumseh on a 22" yard machine snow thrower, the engine will only stay..."
AnonymousAnonymous posted an answer for this Garden:
"Remove the fuel line from the carburetor and check for fuel flow from the line--it should..."
AnonymousAnonymous posted an answer for this Garden:
"I just purchsed. a 2088ccOHV Horizontal Shaft snowblower. I'm a bit lost with the..."
AnonymousAnonymous posted an answer for this Garden:
"Use either starter. The pull start is for when the engine stalls on the job, and you are..."
Anonymous
Anonymous posted an answer for this Hand Tools:
"Just pull the spring assembly out completely (silver thingy), slide one full length of..."
AnonymousAnonymous posted an answer for this Hand Tools:
"how do you fill JT-21 staple gun? I have JT 5/16 inch staples. I know to fill from the..."
AnonymousAnonymous posted an answer for this Garden:
"in measuring for closet designs, i need to change inches to metric"
AnonymousAnonymous posted an answer for this Garden:
"1-inch = 25.4 mM 39.37-inches = 1-M"
AnonymousAnonymous posted an answer for this Garden:
"If the belts are intact, then NAPA or a hardware store should be able to replace them. If..."
AnonymousAnonymous posted an answer for this Garden:
"The blower won't throw snow - especially heavy snow. Auger and impeller turn but bog..."
AnonymousAnonymous posted an answer for this Garden:
"Either the compressor cannot reach the set limit pressure due to bad valves (usually), or..."
AnonymousAnonymous posted an answer for this Garden:
"my compresser runs and wont cut off"
Anonymous
Garden 1382 answers
Cars & Trucks 1171 answers
Washing Machines 320 answers Dryers 231 answers
Motorcycles 158 answers Dishwashers 122 answers
Computers & Internet 112 answers
Vacuums 111 answers
Microwave Ovens 82 answers
Office Equipment &... 69 answers
