Koolatron 401- 572 Black 12 Volt Canister Vacuum - Page 4 - Answered Questions & Fixed issues
My new beldray 12 in 1 steam mop makes a clicking noise when using?
I don't find specific information about this problem. Here are some things to try. If they don't work, you may call beldray customer service. Check the water tank: Ensure that the water tank is filled with enough water and is properly inserted into the mop.
Clean the mop head: Remove the mop head and clean it thoroughly. Dirt or debris on the mop head can cause clicking noises.
Check for blockages: Check for any blockages in the nozzle or steam outlet. You can use a needle or pin to remove any blockages.
Descale the mop: If your mop has not been descaled in a while, it could be causing the clicking noise. You can descale your mop by following the instructions in the user manual.
10/22/2023 1:55:03 PM •
Vacuums
•
Answered
on Oct 22, 2023
•
121 views
Why doesnt my Haan steamer turn on
If your Haan steamer is not turning on, there could be various reasons for this. Here are some troubleshooting procedures to assist you in identifying and maybe resolving the issue:
Check the Power Source: Make sure the steamer is plugged into a working power source. Check if the outlet is operational by using another device or appliance.
Inspect the Power Cord: Look for any visible damage, such as frayed or exposed wires, on the power cord. If there is any damage to the cord, do not use the steamer until it has been fixed or replaced.
Safety Locks and Buttons: Some steamers feature safety locks or buttons that must be engaged before the unit will turn on. Check the user handbook for any special instructions regarding these safety measures.
Water Reservoir: Ensure that the water reservoir is appropriately filled. Many steamers require water to generate steam, therefore they may not operate if the reservoir is empty or the water level is too low.
Safety systems: Some steamers have safety systems that prohibit them from starting if specific requirements are not satisfied. For example, the steamer may need to reach a certain temperature before it can be used. Allow the steamer some time to attain the required temperature.
Overheating Protection: If the steamer includes overheating protection, it will stop down briefly if it becomes too hot. Allow the steamer to cool before using it again.
A malfunctioning power switch or electrical circuitry could be the source of the problem. If you've examined all of the external causes and the steamer still won't switch on, it may need to be inspected and repaired by an expert.
I hope you can solve your problem.
9/10/2023 12:02:51 AM •
Vacuums
•
Answered
on Sep 10, 2023
•
153 views
Brush roller not rotating
Full 'make model (what it is)' is needed in all questions on Fixya please.
The drive belt is broken whether it is a standalone upright cleaner or whether it is a canister vacuum with a hose and wand with brush head.
How you replace it is completely dependent on make and model, but can easily be Googled or refer to the manual.
8/29/2023 2:52:16 AM •
Vacuums
•
Answered
on Aug 29, 2023
•
52 views
How should hardwood floors be maintained and cleaned ?
- Sweep, dust or dry mop daily.
- Vacuum weekly.
- Clean heavy-traffic areas with a damp mop twice a month.
- Clean with recommended hardwood floor cleaner once a month.
- Apply a fresh coat of finish every three to five years
8/8/2023 11:48:58 AM •
Vacuums
•
Answered
on Aug 08, 2023
•
303 views
Unit will not come on like on a panel say that it has to be drainedHowever, there is no water in the tank. What can I do?
- Check the drain system: Make sure that the drain valve or plug is fully closed and not leaking. If there is any water present, drain it completely before proceeding.
- Reset the unit: Turn off the unit and unplug it from the power source. Wait for a few minutes, then plug it back in and turn it on again. This can sometimes reset any error messages and resolve the issue.
- Check the water detection sensor: The unit may have a sensor that detects the presence of water in the tank. Look for the sensor and make sure it is clean and free of any obstructions. If there is any dirt or debris on the sensor, clean it gently with a soft cloth.
- Contact customer support: If none of the above steps work, it's best to reach out to the manufacturer's customer support for further assistance. They can provide specific troubleshooting steps for your particular unit and guide you through the process of resolving the issue.
Remember to refer to the user manual that came with your unit for specific instructions and recommendations.
7/29/2023 2:09:18 PM •
Vacuums
•
Answered
on Jul 29, 2023
•
52 views
I have a living solutions steam vac model#zq012-a and the cap won't stay down so the pressure won't build up c
If the cap on your Living Solutions steam vac won't stay down, it could be due to a couple of reasons:
- Incorrect positioning: Make sure the cap is properly aligned and seated on the unit. Check if there are any obstructions or debris preventing it from fitting securely. Clean the cap and the sealing surface if necessary.
- Damaged or worn-out seal: The cap may not stay down if the seal inside is damaged or worn out. Inspect the seal for any signs of cracks, tears, or deterioration. If it's damaged, you may need to replace it. Contact the manufacturer or refer to the user manual for guidance on obtaining a replacement seal.
- Defective cap or pressure release mechanism: It's possible that the cap or the pressure release mechanism itself is defective. If you've ruled out other causes and the issue persists, you might need to contact the manufacturer's customer support for further assistance. They may be able to provide troubleshooting steps or offer a replacement part if needed.
Remember to always follow the manufacturer's instructions and safety guidelines when working with steam cleaning devices.
7/16/2023 2:53:28 AM •
Vacuums
•
Answered
on Jul 16, 2023
•
41 views
Not finding what you are looking for?
