Invicta Pro Diver Collection Grand Diver Alarm #3443 Watch for Men - Page 6 - Answered Questions & Fixed issues
Manual for rawlings 78001 watch
press and hold mode, a digit should flashpress another button and change the digitpress mode again, different digit should flash, change it, repeat until complete
10/14/2012 2:35:43 PM •
Invicta Watches
•
Answered
on Oct 14, 2012
•
202 views
I have an invicta lupah
Yes it can be replaced a scratchable sappire crystal,it maybe available to authorized service center near to place.Whatever the result feel free to ask or post a question..
Hope this may help;
Regards,
VOTIT
DON'T FORGET TO RATE;
8/17/2012 2:13:13 AM •
Invicta Watches
•
Answered
on Aug 17, 2012
•
196 views
I have a invicta watch,
Look for the Invicta watch band on eBay.
Any watch band that is the same width at the watch connecting
location will fit. It need not be an Invicta band. Four posts project
from the watch case; two on each -- top and bottom. Measure the
distance between the posts, make sure that the band you obtain
will fit snugly between the posts. Be sure to get the correct size
of mounting pins to install the band on the watch properly.
8/21/2011 7:11:14 AM •
Invicta Watches
•
Answered
on Aug 21, 2011
•
106 views
How do I adjust the
Hi ckward343,
Please follow these steps to adjust the metal band of your watch.
1. Choose a clean, flat surface where you can perform the band adjustment on your Invicta watch. The area you select should be well-lit to illuminate the small watch band components. Place a soft cloth over your work surface to protect the face of your Invicta watch from being scratched or scuffed during band adjustment.
2. Remove the clasp of your Invicta watch band. The watch band clasp is held in place by a spring-loaded metal pin. Exert pressure on the pin with a watch pin removal tool; the pin will not come out but will move over just enough to allow you to separate the clasp from the rest of the watch band.
3. Lay your Invicta watch face down on the soft protective cloth so you can examine the back of the watch band. The watch links engraved with small arrows indicate the removable links, as well as which direction the link pins must be pushed to remove them.
4. Turn your attention to the last link on the side of the watch band without the clasp. Use a watch pin removal tool, or push pin, to push the link pin the direction of the arrow. Once the pin has been removed, the last link on the watch band will come free. Repeat this step to remove additional watch links, as necessary.
5. Lengthen your Invicta watch band by adding additional watch links. Remove the watch band clasp as described in Step 2. Fit the additional watch link to the last link on your Invicta watch band. Insert the link pin and apply gentle pressure to push it all the way in.
6. Reattach the clasp to the end of your Invicta watch band. Push in the spring-loaded metal pin, fit the clasp and watch band pieces together and then release the spring-loaded pin to hold the band in place.
Note: Self-adjusting the band on your Invicta watch may void its warranty. If you want to keep your watch under warranty, have your watch band sized at a local jewelry store for a nominal fee.
Hope it helps.
Thank you for using FixYa.
7/24/2011 2:12:11 PM •
Invicta Watches
•
Answered
on Jul 24, 2011
•
864 views
I just got a Invicta
this watch has a screw down crown. lift up the protector bar or start to unscrew down until it pops out, then turn slowly and pul gently all way out. set the time . tere is 2 positions there. full out time and inbetwwen them is the date and day settings.when there turn up or down until date chages, if it has day and date , up is day down is date.you have to turn few times for it to move..set the date ,set day before and go around . the 12 see number change to might date, set the correct time am or pm. push the crown in and screw in up til hand tight.
6/17/2011 11:02:44 PM •
Invicta Watches
•
Answered
on Jun 17, 2011
•
1,967 views
I recently purchased an Invicta
You're probably pulling it out to hard. Solution: pull the stem out completely and carefully try to push it back in for one click only, then attempt to set the date. If this doesn't work, return the watch as it is defective.
6/9/2011 10:22:34 AM •
Invicta Watches
•
Answered
on Jun 09, 2011
•
173 views
Cannot set Day on Invicta
To set the day and date, gently pull the crown out to the first "ClickStop"
-
- Rotate the crown clockwise to advance the day indicator.
- Rotate the crown counterclockwise to advance the date indicator.
- To set the time, gently pull out the crown to the second "Click Stop" (See fig. C) and rotate the crown to the time of day.
- After day and date are set, push the crown back to it's "Normal Operating" (See fig. A) to start the timepiece running.
5/14/2011 9:26:07 PM •
Invicta Watches
•
Answered
on May 14, 2011
•
951 views
I recently bought an invicata
It looks like your watch has mechanical issue. Without inspecting the watch it's hard to say what exactly the problem is and I suggest you return it for replacement under warranty.
4/15/2011 3:11:57 PM •
Invicta Watches
•
Answered
on Apr 15, 2011
•
954 views
How do i get links
For removing or adding links firstly you will have to remove bracelet pins or screws. In case if there are screw on each side of bracelet - you have to use two screwdrivers simultaneously. In case if there are pins - read the rest:
You may or may not have arrows inside bracelet. Arrows are pointing the way the pins must come out. First you have to find out what sort of pins or even screws are used to keep links together (screw ends and pin end may look similar). Examine both bracelet sides and find the side where pin ends have a groove. Start with a tiny screwdriver and try to unscrew one. If it turns, but doesn't come out, that means you have a pins instead of screws. For removing pins the best would be pin removing tool (approx.5GBP on ebay), but it's possible to do the job without it. Take a hardened steel needle and blunt the sharp end to the approx. size of pin end diameter using any sharpening stone or sandpaper. Get an old towel and fold it to make a soft base for work (like small cusion). As you don't have a special bracelet holder you will need a pair of helping hands to hold the bracelet steady upright. You will need small hammer and pair of flat nose pliers as well. NOTE: The pins MUST be driven split end out first, not vice versa. Make sure that the grooved pin ends are facing towel, not the needle and hammer. Now place the watch on the folded towel, take that needle and smallest hammer you have and start driving the pin out using light blows. Do Not hit hard, as you will brake the needle, scratch your watch or even injure yourself. Watchmakers are using 45 gram hammer, so, calculate your strength of blows. After a few punches check if the split end is coming out and when you see that the pin end is coming out long enough - grab it with pliers and pull the pin out with pliers. When pulling, do NOT turn pliers, as pins tend to brake when twisted. Use firm grip and your strength to pull the pin without twisting. After shortening the bracelet or adding extra link(s) make sure that the pins go back EXACTLY the same way as they came out- the blunt end first in the hole and the split (grooved) end last. Before doing that check remaining pins in bracelet to make sure that you put them back from the right side of bracelet. It is recommended to use plastic hammer to drive pins back in or you will scratch or damage bracelet. If plastic hammer is not available use an old toothbrush handle (or some plastic item) as an absorber. Simply put pin into the hole as deep as you can with your fingers, put the toothbrush handle on split pin end and hit handle, not the pin. Make sure that pin ends are flush with bracelet. If needed- hit few more times. Job done! If you do not want to do it yourself, any jeweler will do it in a matter of few minutes
4/4/2011 2:03:39 AM •
Invicta Watches
•
Answered
on Apr 04, 2011
•
1,054 views
I HAVE AN INVICTA PROFESSIONAL
I was not able find information on your specific model; only 2010 models seem to be listed on the website.
Instruction Manual for Invicta watches:
http://www.invictawatch.com/support_files/instruction_manual/Manual-HiRes.pdf
Go to page 8 of this file to identify the instructions for your watch. For most watches the crown pulls out for setting either to postion 1 or position 2.
Some Invicata watches do have Screw Down Crowns but this would be most likey on a Diver model, to help prevent water infiltration. In order to adjust the date and/or time on such a watch, you must first unscrew the crown before you can gently pull it out to its first or second click stop position. To do this, simply rotate the crown counterclockwise until it springs open. When you have finished setting the watch, the crown must then be pushed in and screwed back in tightly. Not doing so will cancel the water resistance of the watch and will void all warranties from the manufacturer.
3/21/2011 4:31:48 AM •
Invicta Watches
•
Answered
on Mar 21, 2011
•
265 views
MY INVICTA IS AN AUTOMATIC
If hand winding does not work then try waving it gently from side to side for 100-200 times (yes! that is what some makers recommend).
Since self winding watches thrive on use, it is best to wear it daily to keep it functioning.
5/22/2011 3:31:41 AM •
Invicta Watches
•
Answered
on May 22, 2011
•
1,717 views
I have a new invicta
The trick to setting the 24hr hand on the 6089 is to pull the crown out only one notch (not two) before using the upper push button to change the time. As it's a 24hr hand, the best time to set it is at the top of the hour.
2/14/2011 7:29:22 PM •
Invicta Watches
•
Answered
on Feb 14, 2011
•
263 views
Not finding what you are looking for?
